Our most energy-efficient benchtop hoods have containment-enhancing features that allow them to operate at face velocities as low as 60 fpm.Their integrated sash position sensors automatically adjust the blower speed as the sash is raised or lowered.
Protector XStream I-S Laboratory Hoods
The Protector XStream I-S Laboratory Hood takes containment, safety and energy savings to the extreme.With integrated sash position blower controls, this hood was designed for use with Intelli-Sense Multi-Speed Blowers.As the sash is raised or lowered, sensors alert the blower to change speeds to maintain a safe face velocity.That face velocity is displayed on the factory-installed Guardian™ Digital Airflow Monitor for users' peace of mind.
This general chemical, high performance fume hood was independently tested and challenged well beyond the SEFA-1 standards.With a face velocity of 40 fpm and sash fully open, the Protector XStream I-S was subjected to 50 fpm cross drafts, NIH protocol, and tracer gas measurements in the chest of the mannequin.In all scenarios, the Protector XStream I-S allowed 0.00 ppm average level of tracer gas outside the fume hood.Although your safety officer will determine the actual face velocity setting for your laboratory, the ability of this hood to contain under these adverse conditions sets a new standard of safety.
Safety is foremost, but energy savings is equally impressive.Although face velocity is a factor, it's the volumetric rate (CFM) that determines the energy consumption.Operating a 6' Protector XStream I-S at 60 fpm face velocity, with the sash in its fully open position, requires only 690 CFM.Regardless of your desired operating face velocity, the Protector XStream I-S yields the lowest required CFM of any hood.
betway官网下载appFilter these products
Showing 1 - 16 of 16 Results
4' Protector XStream I-S Laboratory Hood
Catalog #110416000
- Nominal Width:4'
- Blower Requirements:Remote blower required
- Exterior Depth:37.7" (95.8 cm)
- Service Fixtures:0
- Style:Benchtop
4' Protector XStream I-S Laboratory Hood
Catalog #110416020
- Nominal Width:4'
- Blower Requirements:Remote blower required
- Service Fixtures:0
- Style:Benchtop
4' Protector XStream I-S Laboratory Hood with 2 service fixtures
Catalog #110416021
- Nominal Width:4'
- Blower Requirements:Remote blower required
- Exterior Depth:37.7" (95.8 cm)
- Service Fixtures:2
- Style:Benchtop
4' Protector XStream I-S Laboratory Hood with 2 service fixtures and 1 electrical duplex
Catalog #110416002
- Nominal Width:4'
- Blower Requirements:Remote blower required
- Exterior Depth:37.7" (95.8 cm)
- Service Fixtures:2 and GFCI Duplex
- Style:Benchtop
5' Protector XStream I-S Laboratory Hood
Catalog #110516000
- Nominal Width:5'
- Blower Requirements:Remote blower required
- Exterior Depth:37.7" (95.8 cm)
- Service Fixtures:0
- Style:Benchtop
5' Protector XStream I-S Laboratory Hood
Catalog #110516020
- Nominal Width:5'
- Blower Requirements:Remote blower required
- Service Fixtures:0
- Style:Benchtop
5' Protector XStream I-S Laboratory Hood with 2 service fixtures
Catalog #110516021
- Nominal Width:5'
- Blower Requirements:Remote blower required
- Exterior Depth:37.7" (95.8 cm)
- Service Fixtures:2
- Style:Benchtop
5' Protector XStream I-S Laboratory Hood with 2 service fixtures and 1 electrical duplex
Catalog #110516002
- Nominal Width:5'
- Blower Requirements:Remote blower required
- Exterior Depth:37.7" (95.8 cm)
- Service Fixtures:2 and GFCI Duplex
- Style:Benchtop
6' Protector XStream I-S Laboratory Hood
Catalog #110616000
- Nominal Width:6'
- Blower Requirements:Remote blower required
- Exterior Depth:37.7" (95.8 cm)
- Service Fixtures:0
- Style:Benchtop
6' Protector XStream I-S Laboratory Hood
Catalog #110616020
- Nominal Width:6'
- Blower Requirements:Remote blower required
- Service Fixtures:0
- Style:Benchtop
6' Protector XStream I-S Laboratory Hood with 2 service fixtures
Catalog #110616021
- Nominal Width:6'
- Blower Requirements:Remote blower required
- Exterior Depth:37.7" (95.8 cm)
- Service Fixtures:2
- Style:Benchtop
6' Protector XStream I-S Laboratory Hood with 2 service fixtures and 1 electrical duplex
Catalog #110616002
- Nominal Width:6'
- Blower Requirements:Remote blower required
- Exterior Depth:37.7" (95.8 cm)
- Service Fixtures:2 and GFCI Duplex
- Style:Benchtop
8' Protector XStream I-S Laboratory Hood
Catalog #110816000
- Nominal Width:8'
- Blower Requirements:Remote blower required
- Exterior Depth:37.7" (95.8 cm)
- Service Fixtures:0
- Style:Benchtop
8' Protector XStream I-S Laboratory Hood
Catalog #110816020
- Nominal Width:8'
- Blower Requirements:Remote blower required
- Service Fixtures:0
- Style:Benchtop
8' Protector XStream I-S Laboratory Hood with 2 service fixtures
Catalog #110816021
- Nominal Width:8'
- Blower Requirements:Remote blower required
- Exterior Depth:37.7" (95.8 cm)
- Service Fixtures:2
- Style:Benchtop
8' Protector XStream I-S Laboratory Hood with 2 service fixtures and 2 electrical duplexes
Catalog #110816002
- Nominal Width:8'
- Blower Requirements:Remote blower required
- Exterior Depth:37.7" (95.8 cm)
- Service Fixtures:2 and GFCI Duplex
- Style:Benchtop
Our Product Representatives Are Here To Help
必威平台官网首页Labconco Fume Hood Airflow Demonstration
必威平台官网首页Labconco Protector Fume Hoods include the XStream, the most energy-efficient ducted fume hood design, as well as other high performance ducted fume hoods in our Premier and XL lines.This video demonstrates the airflow and safety features of all our Protector Fume Hood models.
Chemical Fume Hood Installation
必威平台官网首页This video shows how to install a Labconco Protector Fume Hood.This video features a Protector XStream Fume Hood, and most installations are similar.
How the I-S Fume Hood Saves Energy
This animation shows how the Protector I-S works with a laboratory air supply's pressure differential switch to save energy.When the sash is lowered, blower speed is automatically reduced to conserve the room's tempered air.
Literature & Resources
lock必威官方 orregisterto download resourcesBrochures
Protector XStream I-S, Premier I-S and XL I-S Laboratory Fume Hoods Brochure
This brochure contains descriptions, dimensional data and ordering information on Protector XStream I-S, Premier I-S and XL I-S Laboratory Fume Hoods.These hoods feature integrated sash position sensors linked to the factory-installed Intelli-Sense Blower control box.The required blowers are listed.Standards related to hoods are also provided.
User's Manuals
Protector XStream Laboratory Hoods Manual
For Protector XStream and Protector XStream I-S Laboratory Fume Hoods 11041, 11051, 11061 and 11081 Series.
betway官网下载appRelated Products
Airflow Monitors
These monitors, used for a variety of fume hoods, enclosures and glove boxes, sense airflow and alert the user to low airflow conditions.
Base Cabinets
必威平台官网首页Base Cabinets provide support for the full line of benchtop Labconco fume hoods and other enclosures and may be mixed or matched so that total width equals the width of the hood.
Ductwork and Blower Accessories
必威平台官网首页Labconco offers a full line of ductwork, filter packs and transition pieces to complete your exhaust system.
Fume Hood Accessories
必威平台官网首页Labconco offers a complete line of accessories to customize your Protector, Basic or Fiberglass 30 Laboratory Hood.
Remote Blowers & Exhausters
Remote blowers, designed for roof-mounting, provide airflow for fume hoods and other enclosures.Exhausters, designed for ductless applications, filter the air before returning it to the lab.
Work Surfaces
必威平台官网首页Labconco offers dished and flat solid epoxy and flat stainless steel work surfaces that work with a number of Labconco fume hoods and enclosures.
